Make sure this part fits your vehicle

Honda 22810-PLW-005 Bearing, Clutch Release (Nsk)

1992-2019 Honda 22810PLW005

Honda 22810-PLW-005 Bearing, Clutch Release (Nsk)
  • Part Description
    Release Bearing
  • Replaces
    22810-P20-005
  • Manufacturer
    Honda
Customer Questions & Answers
$70.86 MSRP: $100.08
You Save: $29.22 (30%)
1
ADD TO CART
  • Product Specifications

    BrandGenuine Honda
    Manufacturer Part Number22810-PLW-005
    Part DescriptionRelease Bearing
    Item Dimensions3.0 x 2.6 x 1.4 inches
    Item Weight0.50 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces22810-P20-005
    ManufacturerHonda
    SKU22810-PLW-005
    WarrantyThis genuine Honda part is guaranteed by Honda's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Body & Trim Emission & Transmission
    2016 Honda CR-Z3 Door EX, 3 Door EX-L, 3 Door LXKA 6MT
    2015 Honda CR-Z3 Door Base, 3 Door EXKA 6MT
    2014 Honda CR-Z3 Door Base, 3 Door EXKA 6MT
    2013 Honda CR-Z3 Door Base, 3 Door EXKA 6MT
    2012 Honda CR-Z3 Door Base, 3 Door EXKA 6MT
    2011 Honda CR-Z3 Door Base, 3 Door EXKA 6MT
    2015 Honda Civic2 Door EX, 2 Door LX, 4 Door LXKA 5MT
    2014 Honda Civic2 Door EX, 2 Door LX, 4 Door LXKA 5MT
    2013 Honda Civic2 Door EX, 2 Door LX, 4 Door LXKA 5MT
    2012 Honda Civic2 Door DX, 2 Door EX, 2 Door LX, 4 Door DX, 4 Door LXKA 5MT
    View More

Customer Questions & Answers

Q:
I just wanted to verify fitment prior to ordering part Posted by HondaPartsNow Specialist
A:
You can Select Your Vehicle to check if 22810-PLW-005 fits your vehicle.
Posted by HondaPartsNow Specialist
Q:
How do you remove the transaxle from the 2015 Honda Civic? Posted by Customer
A:
Remove the transaxle.
Posted by HondaPartsNow Specialist
See expert answers on similar Release Bearing
Q:
What should be done to support the clutch disc during removal from the 2013 Honda Civic? Posted by Customer
A:
Install a clutch alignment tool through the clutch disc hub.
Posted by HondaPartsNow Specialist
See expert answers on similar Release Bearing
Q:
How to replace a Clutch Release Bearing and Clutch Fork? Posted by Customer
A:
Unbolt the clutch release cylinder, but don't disconnect the fluid line between the master cylinder and the release cylinder. Suspend the release cylinder out of the way with a piece of wire. Remove the transaxle. Slide the release bearing off the input shaft, disengage the clutch release fork retention spring from the ball stud and remove the fork. Hold the bearing by the outer race and rotate the inner race while applying pressure. If the bearing doesn't turn smoothly or if it's noisy, replace the bearing/hub assembly with a new one. Wipe the bearing with a clean rag and inspect it for damage, wear and cracks. It's common practice to replace the bearing with a new one whenever a clutch job is performed, to decrease the possibility of a bearing failure in the future. Don't immerse the bearing in solvent - it's sealed for life and to do so would ruin it. Also check the release lever for cracks and bends. If the new bearing is not equipped with a bearing holder (hub), drive the holder from the old bearing and install it to the new one. A seal/bushing driver or an appropriately sized socket can be used to accomplish this. Fill the inner groove of the release bearing with high temperature grease. Also apply a light coat of the same grease to the transaxle input shaft splines and the front bearing retainer. Lubricate the release fork ball socket, fork ends and release cylinder pushrod socket with high temperature grease. Attach the release bearing to the release fork. Slide the release bearing onto the transaxle input shaft front bearing retainer while passing the end of the release fork through the opening in the clutch housing. Push the clutch release fork onto the ball stud until it's firmly seated. Apply a light coat of high temperature grease to the face of the release bearing where it contacts the pressure plate diaphragm fingers. The remainder of installation is the reverse of the removal procedure.
Posted by HondaPartsNow Specialist
Q:
What should be done to support the clutch disc during removal from the 1993 Honda Del Sol? Posted by Customer
A:
Install a clutch alignment tool through the clutch disc hub.
Posted by HondaPartsNow Specialist
See expert answers on similar Release Bearing
If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Honda Part 22810-PLW-005, the Right Choice

Your vehicle deserves only genuine OEM Honda parts and accessories. To ensure reliability, purchase Honda part # 22810-PLW-005 Bearing, Clutch Release (Nsk). It is sometimes referred to as Honda Release Bearing. Our Honda parts and accessories are expedited directly from authorized Honda dealers strategically located all across the U.S. and are backed by the manufacturer's 12 month, 12,000 mile warranty. OEM Honda parts are the best for restoring your vehicle to factory condition performance. This part fits 1992-2015 Honda Civic, 1993-1997 Honda Del Sol, 2007-2019 Honda Fit, 2000-2006 Honda Insight.

Affordable, reliable and built to last, Honda part # 22810PLW005 Bearing, Clutch Release (Nsk) stands out as the smart option. HondaPartsNow.com is your prime online source with the biggest and best selection of genuine Honda parts and accessories at giant discounted prices. We have the OEM Honda parts and accessories you need at the wholesale prices. HondaPartsNow.com has you covered no matter what type of Honda vehicle you drive.

Why choose Honda Parts Now

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly