How to remove and install a Steering Knuckle on Honda Civic?

Loosen the wheel lug nuts, raise the vehicle and support it securely on jackstands. Remove the wheel. Remove the driveaxle/hub nut. Remove the brake caliper and support it with a piece of wire. Remove the caliper mounting bracket, then remove the brake disc from the hub. Remove the stabilizer end link nut. Mark the strut to the steering knuckle then remove the strut-to-steering knuckle nuts, but do not remove the bolts. Detach the ABS wheel speed sensor from the steering knuckle. Separate the control arm from the balljoint. Detach the tie-rod end from the steering knuckle. Push the driveaxle from the hub. Support the end of the driveaxle with a piece of wire. Remove the bolts and separate the steering knuckle from the strut. Installation is the reverse of removal. Guide the knuckle and hub assembly into position, inserting the driveaxle into the hub. Push the knuckle into the strut flange and install the bolts and nuts, but don't tighten them yet. Connect the balljoint to the control arm and tighten the fasteners. Tighten the strut bolt nuts and the tie-rod end nut. Place the brake disc on the hub and install the caliper mounting bracket and caliper. Install the driveaxle/hub nut and tighten it. Install the wheel and lug nuts. Lower the vehicle and tighten the lug nuts. Have the front wheel alignment checked and, if necessary, adjusted.

How to remove a rear Trailing Arm and Steering Knuckle on Honda Civic?

Place jackstands under the rear of your car to lift it off the ground, but secure it first. Loosen each lug nut holding the rear wheel. Block the front wheels so the car can't roll. After jacking up the car, use jack stands to keep it steady while you do the work. When lifting, place a jack under the trailing arm and take off the wheel first. Unbolt the top part of the arm where it meets the Steering Knuckle and remove the other bolt(s) on the inner end of the arm. Start installation by reversing the removal steps, lift the trailing arm with a floor jack until the wheels are at their typical ride height, and then secure all bolts and wheel lug nuts. Take off the brake hose and ABS sensor holder screws using the floor jack under the pinon again. Remove the rear underbody splash shield when necessary. Mark where the trailing arm adjusting cam connects to the knuckle bolt, then take off the bottom shock absorber bolt and the bolts holding the arm to the knuckle. Free the arm from the knuckle while keeping the knuckle in place with a bungee cord or wire. Remove these parts from the suspension system: 1) Disconnect the trailing arm's link to the stabilizer bar, 2) Pull out the shock absorber's lower mounting, 3) Remove the bolts that hold the front of the trailing arm to the chassis. Baseball cap first, lower the floor jack calmly, and pull off the coil spring. Unscrew and take out the bolt attaching the trailing arm to the car body. Also remove the trailing arm itself from the vehicle. To install, line up two marks - one on the adjuster cam and the other on the trailing arm - then raise the arm with the floor jack until it reaches standard ride height before tightening all fasteners. Remember to also tighten the wheel lug nuts, check the rear wheel alignment, and torque all bolts correctly. After discarding the brake drum or brake caliper and disc, take off the parking brake shoes, wheel speed sensor, and turn off the parking brake cable if your car has it. After positioning a floor jack under the trailing arm, take off the suspension arms from the knuckle and remove the entire rear wheel bearing hub assembly. If your car has drum brakes, take off the brake backing plate also attached to the brake shoes. Take off the fasteners from both the upper and lower part of the knuckle while noting where the cam bolt goes, so you can put them back later. Uninstall the parts in reverse order, keeping the trailing arm held up by a floor jack until you reach normal ride height. Then tighten all suspension arm hold downs to the right torque, and mark matchpoints on the toe adjusting cam. Snug down the caliper mounting bolts to their correct torque. Brake bleeding isn't needed but will require bleed line repair if any hydraulic lines were made loose. After installing, check and adjust wheel alignment if needed.

Genuine Honda Civic Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

137 Steering Knuckles found

View related parts
Honda Civic Knuckle Complete, Right Rear
Part Number: 52210-TBA-A00
$130.79 MSRP: $186.32
You Save: $55.53 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2021 Honda Civic | 2 Door EX, 2 Door EX (Turbo), 2 Door EX (Turbo/6MT), 2 Door EX (Turbo/CVT), 2 Door LX, 2 Door LX (6MT), 2 Door LX (CVT), 2 Door SI, 2 Door Sport, 2 Door Sport (6MT), 2 Door Sport (CVT), 2 Door Touring, 2 Door Touring (Turbo), 4 Door EX, 4 Door EX (Turbo), 4 Door EX-A, 4 Door EX-T, 4 Door EX-TA, 4 Door EX-TL, 4 Door EX-TLA, 4 Door LX, 4 Door LX (6MT), 4 Door LX (CVT), 4 Door LX-A, 4 Door SE, 4 Door SI, 4 Door Sport, 4 Door Sport (6MT), 4 Door Sport (CVT), 4 Door Touring, 4 Door Touring (Turbo), 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door SE, 5 Door Sport | KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic Left Front Knuckle
Part Number: 51216-TGN-G01
$179.55 MSRP: $255.77
You Save: $76.22 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle, Left Front; Knuckle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2020 Honda Civic | 2 Door SI, 4 Door SI | KA 6MT
View related parts
Honda Civic Knuckle Right Front
Part Number: 51211-TBC-A01
$170.62 MSRP: $243.05
You Save: $72.43 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Front Passenger Side
- Replaced by: 51211-T20-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2021 Honda Civic | 2 Door EX, 2 Door EX (Turbo), 2 Door EX (Turbo/6MT), 2 Door EX (Turbo/CVT), 2 Door Sport, 2 Door Sport (6MT), 2 Door Sport (CVT), 2 Door Touring, 2 Door Touring (Turbo), 4 Door EX, 4 Door EX (Turbo), 4 Door EX-T, 4 Door EX-TA, 4 Door EX-TL, 4 Door EX-TLA, 4 Door Sport, 4 Door Sport (6MT), 4 Door Sport (CVT), 4 Door Touring, 4 Door Touring (Turbo) | KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic Right Front Knuckle
Part Number: 51211-TBA-A03
$210.33 MSRP: $320.87
You Save: $110.54 (35%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Passenger Side
- Replaces: 51211-TBA-A01, 51211-TBA-A02
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2021 Honda Civic | 2 Door LX, 2 Door LX (6MT), 2 Door LX (CVT), 4 Door EX, 4 Door EX-A, 4 Door LX, 4 Door LX (6MT), 4 Door LX (CVT), 4 Door LX-A, 4 Door SE | KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic Left Front Knuckle
Part Number: 51216-TR0-A50
$225.31 MSRP: $320.95
You Save: $95.64 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2013-2015 Honda Civic | 2 Door EX, 2 Door EX-L, 2 Door LX, 4 Door EX, 4 Door EX-L, 4 Door GX, 4 Door HF, 4 Door LX, 4 Door MX, 4 Door MX (Hybrid) | KA 5AT, KA CVT, KL 5AT, KL CVT
View related parts
Honda Civic Right Front Knuckle
Part Number: 51211-TGN-G01
$179.55 MSRP: $255.77
You Save: $76.22 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle, Right Front; Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2020 Honda Civic | 2 Door SI, 4 Door SI | KA 6MT
View related parts
Honda Civic Right Front Knuckle
Part Number: 51211-TR0-A50
$219.53 MSRP: $320.95
You Save: $101.42 (32%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2013-2015 Honda Civic | 2 Door EX, 2 Door EX-L, 2 Door LX, 4 Door EX, 4 Door EX-L, 4 Door GX, 4 Door HF, 4 Door LX, 4 Door MX, 4 Door MX (Hybrid) | KA 5AT, KA CVT, KL 5AT, KL CVT
View related parts
Honda Civic Right Front Knuckle
Part Number: 51211-TGG-A01
$179.61 MSRP: $255.85
You Save: $76.24 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle, Right Front; Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2021 Honda Civic | 5 Door Sport | KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic Left Front Knuckle
Part Number: 51216-SNA-010
$320.10 MSRP: $455.98
You Save: $135.88 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2006-2011 Honda Civic | 2 Door DX, 2 Door EX, 2 Door EX-L, 2 Door LX, 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door GX, 4 Door LX, 4 Door LX-S, 4 Door MX (Hybrid) | KA 5AT, KA 5MT, KA CVT
View related parts
Honda Civic Left Front Knuckle
Part Number: 51216-TET-H00
$303.64 MSRP: $432.53
You Save: $128.89 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle, Left Front; Knuckle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2021 Honda Civic | 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door SE | KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic Right Front Knuckle
Part Number: 51211-TET-H00
$303.64 MSRP: $432.53
You Save: $128.89 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle, Right Front; Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2021 Honda Civic | 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door SE | KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic Right Front Knuckle
Part Number: 51211-SNA-010
$315.82 MSRP: $449.88
You Save: $134.06 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2006-2011 Honda Civic | 2 Door DX, 2 Door EX, 2 Door EX-L, 2 Door LX, 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door GX, 4 Door LX, 4 Door LX-S, 4 Door MX (Hybrid) | KA 5AT, KA 5MT, KA CVT
View related parts
Honda Civic Left Front Knuckle
Part Number: 51216-TR7-A10
$517.98 MSRP: $747.45
You Save: $229.47 (31%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Driver Side
- Replaces: 51216-TR7-A00
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2012 Honda Civic | 2 Door SI, 4 Door SI | KA 6MT
View related parts
Honda Civic Knuckle Complete, Front Right
Part Number: 51210-TGH-A51
$592.83 MSRP: $855.45
You Save: $262.62 (31%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Passenger Side
- Replaces: 51210-TGH-A50
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2021 Honda Civic | 5 Door Touring LE, 5 Door Type R, 5 Door Type R (Touring) | KA 6MT
View related parts
Honda Civic Right Front Knuckle
Part Number: 51211-TS9-A02
$991.81 MSRP: $1431.18
You Save: $439.37 (31%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Passenger Side
- Replaces: 51211-TS9-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2014-2015 Honda Civic | 2 Door SI, 4 Door SI | KA 6MT
View related parts
Honda Civic KNUCKLE, FR- R
Part Number: 51211-T20-A01
$170.62 MSRP: $243.05
You Save: $72.43 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Passenger Side
- Replaces: 51211-TBC-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2026 Honda Civic | 2 Door EX, 2 Door EX (Turbo), 2 Door EX (Turbo/6MT), 2 Door EX (Turbo/CVT), 2 Door Sport, 2 Door Sport (6MT), 2 Door Sport (CVT), 2 Door Touring, 2 Door Touring (Turbo), 4 Door 1.5T EX, 4 Door 1.5T EX BD, 4 Door 1.5T Touring, 4 Door 2.0L LX, 4 Door 2.0L Sport, 4 Door EX, 4 Door EX (Turbo), 4 Door EX-T, 4 Door EX-TA, 4 Door EX-TL, 4 Door EX-TLA, 4 Door LX, 4 Door LX 2WD, 4 Door Sport, 4 Door Sport (6MT), 4 Door Sport (CVT), 4 Door Sport 2WD, 4 Door Touring, 4 Door Touring (Turbo), 5 Door 1.5T EX-L, 5 Door 1.5T Sport Touring, 5 Door 2.0L LX, 5 Door 2.0L Sport, 5 Door EX-L, 5 Door LX, 5 Door Sport, 5 Door Sport FWD, 5 Door Sport Touring | 6MT, CVT, KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic KNUCKLE, FR- L
Part Number: 51216-T20-A01
$170.62 MSRP: $243.05
You Save: $72.43 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Driver Side
- Replaces: 51216-TBC-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2026 Honda Civic | 2 Door EX, 2 Door EX (Turbo), 2 Door EX (Turbo/6MT), 2 Door EX (Turbo/CVT), 2 Door Sport, 2 Door Sport (6MT), 2 Door Sport (CVT), 2 Door Touring, 2 Door Touring (Turbo), 4 Door 1.5T EX, 4 Door 1.5T EX BD, 4 Door 1.5T Touring, 4 Door 2.0L LX, 4 Door 2.0L Sport, 4 Door EX, 4 Door EX (Turbo), 4 Door EX-T, 4 Door EX-TA, 4 Door EX-TL, 4 Door EX-TLA, 4 Door LX, 4 Door LX 2WD, 4 Door Sport, 4 Door Sport (6MT), 4 Door Sport (CVT), 4 Door Sport 2WD, 4 Door Touring, 4 Door Touring (Turbo), 5 Door 1.5T EX-L, 5 Door 1.5T Sport Touring, 5 Door 2.0L LX, 5 Door 2.0L Sport, 5 Door EX-L, 5 Door LX, 5 Door Sport, 5 Door Sport FWD, 5 Door Sport Touring | 6MT, CVT, KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic Knuckle Left Front
Part Number: 51216-TBC-A01
$170.62 MSRP: $243.05
You Save: $72.43 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Front Driver Side
- Replaced by: 51216-T20-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2021 Honda Civic | 2 Door EX, 2 Door EX (Turbo), 2 Door EX (Turbo/6MT), 2 Door EX (Turbo/CVT), 2 Door Sport, 2 Door Sport (6MT), 2 Door Sport (CVT), 2 Door Touring, 2 Door Touring (Turbo), 4 Door EX, 4 Door EX (Turbo), 4 Door EX-T, 4 Door EX-TA, 4 Door EX-TL, 4 Door EX-TLA, 4 Door Sport, 4 Door Sport (6MT), 4 Door Sport (CVT), 4 Door Touring, 4 Door Touring (Turbo) | KA 6MT, KA CVT, KL CVT
View related parts
Honda Civic KNUCKLE COMP, RR- R
Part Number: 52210-T20-A00
$172.15 MSRP: $245.23
You Save: $73.08 (30%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2022-2026 Honda Civic | 4 Door 1.5T EX, 4 Door 1.5T EX BD, 4 Door 1.5T Touring, 4 Door 2.0L LX, 4 Door 2.0L Sport, 4 Door EX, 4 Door LX, 4 Door LX 2WD, 4 Door Si, 4 Door Si FWD, 4 Door Si With High Performance Tires, 4 Door Sport, 4 Door Sport 2WD, 4 Door Touring, 5 Door 1.5T EX-L, 5 Door 1.5T Sport Touring, 5 Door 2.0L LX, 5 Door 2.0L Sport, 5 Door EX-L, 5 Door LX, 5 Door Sport, 5 Door Sport FWD, 5 Door Sport Touring | 6MT, CVT
View related parts
Honda Civic Knuckle Complete, Left Rear
Part Number: 52215-TBA-A00
$130.81 MSRP: $186.33
You Save: $55.52 (30%)
Product Specifications
- Other Name: Knuckle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2021 Honda Civic | 2 Door EX, 2 Door EX (Turbo), 2 Door EX (Turbo/6MT), 2 Door EX (Turbo/CVT), 2 Door LX, 2 Door LX (6MT), 2 Door LX (CVT), 2 Door SI, 2 Door Sport, 2 Door Sport (6MT), 2 Door Sport (CVT), 2 Door Touring, 2 Door Touring (Turbo), 4 Door EX, 4 Door EX (Turbo), 4 Door EX-A, 4 Door EX-T, 4 Door EX-TA, 4 Door EX-TL, 4 Door EX-TLA, 4 Door LX, 4 Door LX (6MT), 4 Door LX (CVT), 4 Door LX-A, 4 Door SE, 4 Door SI, 4 Door Sport, 4 Door Sport (6MT), 4 Door Sport (CVT), 4 Door Touring, 4 Door Touring (Turbo), 5 Door EX, 5 Door EX-L, 5 Door LX, 5 Door SE, 5 Door Sport | KA 6MT, KA CVT, KL CVT

| Page 1 of 7 |Next >

1-20 of 137 Results

Honda Civic Steering Knuckle

The Steering Knuckle of Honda Civic relates to the suspension and steering apparatus and guarantees steady turn of the front wheels. It is considered the connection point of control arms, tie-rod ends or steering wheels and spindles or hubs. These Honda Civic Knuckles are categorized by the type of vehicle; rear-wheel drive or front and all-wheel drive since the spindle inclusion and the hub joining method vary. Prevalently sourced from kingpins, steering knuckles are now manufactured to suit modern suspension systems, and are built to be very durable and normally require replacement only when they are damaged. All in all, the Knuckle is instrumental as far as wheel stability and control characteristics of the Honda Civic is concerned.

In search of affordable OEM Honda Civic Steering Knuckle? Consider browsing through our extensive inventory of genuine Honda Civic Steering Knuckle. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Civic Steering Knuckle Parts Questions & Experts Answers

Left Front Knuckle
51216-TR7-A10
Q: How to remove and install a Steering Knuckle on Honda Civic?
A:
Loosen the wheel lug nuts, raise the vehicle and support it securely on jackstands. Remove the wheel. Remove the driveaxle/hub nut. Remove the brake caliper and support it with a piece of wire. Remove the caliper mounting bracket, then remove the brake disc from the hub. Remove the stabilizer end link nut. Mark the strut to the steering knuckle then remove the strut-to-steering knuckle nuts, but do not remove the bolts. Detach the ABS wheel speed sensor from the steering knuckle. Separate the Control Arm from the balljoint. Detach the tie-rod end from the steering knuckle. Push the driveaxle from the hub. Support the end of the driveaxle with a piece of wire. Remove the bolts and separate the steering knuckle from the strut. Installation is the reverse of removal. Guide the knuckle and hub assembly into position, inserting the driveaxle into the hub. Push the knuckle into the strut flange and install the bolts and nuts, but don't tighten them yet. Connect the balljoint to the control arm and tighten the fasteners. Tighten the strut bolt nuts and the tie-rod end nut. Place the brake disc on the hub and install the caliper mounting bracket and caliper. Install the driveaxle/hub nut and tighten it. Install the wheel and lug nuts. Lower the vehicle and tighten the lug nuts. Have the front wheel alignment checked and, if necessary, adjusted.
Right Rear Knuckle
52210-TR0-A50
Q: How to remove a rear Trailing Arm and Steering Knuckle on Honda Civic?
A:
Place jackstands under the rear of your car to lift it off the ground, but secure it first. Loosen each lug nut holding the rear wheel. Block the front wheels so the car can't roll. After jacking up the car, use jack stands to keep it steady while you do the work. When lifting, place a jack under the trailing arm and take off the wheel first. Unbolt the top part of the arm where it meets the Steering Knuckle and remove the other bolt(s) on the inner end of the arm. Start installation by reversing the removal steps, lift the trailing arm with a floor jack until the wheels are at their typical ride height, and then secure all bolts and wheel lug nuts. Take off the brake hose and ABS sensor holder screws using the floor jack under the pinon again. Remove the rear underbody splash shield when necessary. Mark where the trailing arm adjusting cam connects to the knuckle bolt, then take off the bottom shock absorber bolt and the bolts holding the arm to the knuckle. Free the arm from the knuckle while keeping the knuckle in place with a bungee cord or wire. Remove these parts from the suspension system: 1) Disconnect the trailing arm's link to the stabilizer bar, 2) Pull out the shock absorber's lower mounting, 3) Remove the bolts that hold the front of the trailing arm to the chassis. Baseball cap first, lower the floor jack calmly, and pull off the coil spring. Unscrew and take out the bolt attaching the trailing arm to the car body. Also remove the trailing arm itself from the vehicle. To install, line up two marks - one on the adjuster cam and the other on the trailing arm - then raise the arm with the floor jack until it reaches standard ride height before tightening all fasteners. Remember to also tighten the wheel lug nuts, check the rear wheel alignment, and torque all bolts correctly. After discarding the brake drum or brake caliper and disc, take off the parking brake shoes, wheel speed sensor, and turn off the parking brake cable if your car has it. After positioning a floor jack under the trailing arm, take off the suspension arms from the knuckle and remove the entire rear wheel bearing hub assembly. If your car has drum brakes, take off the brake backing plate also attached to the brake shoes. Take off the fasteners from both the upper and lower part of the knuckle while noting where the cam bolt goes, so you can put them back later. Uninstall the parts in reverse order, keeping the trailing arm held up by a floor jack until you reach normal ride height. Then tighten all suspension arm hold downs to the right torque, and mark matchpoints on the toe adjusting cam. Snug down the caliper mounting bolts to their correct torque. Brake bleeding isn't needed but will require bleed line repair if any hydraulic lines were made loose. After installing, check and adjust wheel alignment if needed.

Related Honda Civic Parts

Browse by Year