×
- Hello
- Login or Register
- Quick Links
- Live Chat
- Track Order
- Parts Availability
- RMA
- Help Center
- Contact Us
- Shop for
- Honda Parts
- Honda Accessories
My Garage
My Account
Cart
Genuine Honda CRX Intake Manifold
Engine Intake Manifold- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
17 Intake Manifolds found
Honda CRX Manifold, Intake (Lower)
Part Number: 17100-PE1-663$311.93 MSRP: $444.35You Save: $132.42 (30%)
Honda CRX Intake Manifold
The Intake Manifold of Honda CRX is quite vital because it is responsible for delivering air or air/fuel mixture to the several cylinder and is always out a leader to determine the performance and power output of vehicle's engine. It works with air which is from the throttle body, or carburetor in case where it is a carbureted, throttle body injected or multiport fuel injected engine design. Traditionally, the intake manifolds of Honda CRX were manufactured from cast iron or aluminum but the advanced Honda models today use light weighted composites such as plastics with better fuel efficiency and cooling. Certain models include variable-length intake manifolds (VLIM) that are used to adjust the length of the intake tract in relation to the engine load with the purpose of enhancing the airflow and subsequently, the performance. Taken together the design and the material of the Honda CRX intake manifold will propel the car's engine to its peak performance.
In search of affordable OEM Honda CRX Intake Manifold? Consider browsing through our extensive inventory of genuine Honda CRX Intake Manifold. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.
Honda CRX Intake Manifold Parts Questions & Experts Answers
- Q: How do you remove and install the intake manifold on Honda CRX?A:To replace or remove the intake manifold on carbureted engines, one has to open the drain plug and get a clean pan placed under the Radiator and then drain the cooling system, finally, unplug the negative terminal on the battery. Thirdly, next step is the air cleaner and case and fourth one is to disconnect the carburetor from intake manifold. Remove the emission control hoses on the manifold T-joint, remove the hose above the T-joint leading to the air cleaner check valve and undo the electrical connectors from the thermoswitches. Make sure to unbolt the solenoid valve that is situated near the thermoswitch, and then unbolt the nuts that connect the intake manifold to the cylinder head diagonally and then do away with the manifold. Scrub the mounting surfaces of the gasket with a putty knife. For installation, transfer necessary components to a new manifold if replacing, use new gaskets and sealant if necessary and in the same manner reverse the following steps above while at the same applying water resistant sealer on the new gasket then connect all the hose s then tighten the nuts on the manifold to 16 ft lbs. When installing the carburetor, it is necessary to reinstall the insulator gasket and O-ring, and fasten the mountings nuts to the same level of torque. On fuel injected models take out the negative battery connection and drain the cooling system, label and disconnect the electrical connectors and vacuum lines and do a fuel pressure release. The throttle body assembly or fuel injector manifold must be removed as well as other parts such a fast idle control valve and the EGR valve if needed. Loosen and take off the intake manifold bolts and discard the gaskets if there is an upper and lower manifold chamber. Installation is reverse of removal; clean gasket mating surfaces, use new gaskets, torque intake manifold nuts in a criss cross pattern of 16 ft./lbs. For 1984-87 models, secure the upper manifold to the lower manifold, there should be bolt and nuts that are to be tightened to the specified torque, all hoses and wires should be connected before refilling of the cooling system.
