How to replace the Door Handle, Door Latch Assembly, and Door Lock Cylinder on a Honda Del Sol?

To replace the outside door handle, therefore, one has to take off the inside door handle, the door trim panel as well as a plastic shield. Wind it around the handle opening since this is the area that the paint is most likely to get damaged. For rear doors, a position of rear glass channel must be changed, to do this , the upper channel nut has to be loosened and the lower bolt has to be removed then the channel has to be shifted forward. Secondly, thereafter, unscrew the door handle retaining bolts and if possible do away with the door latch so as to get better access to the door. With the help of a small flat-bladed screwdriver, pry the lock rod loose, pull the handle outwards from the door and turn it anti-clockwise to de-thread it from the release rod. The process of removal is done in an order of inversion to the process of installation. The lock cylinder can be replaced by first removing the outside door handle and by pulling a retainer clip to remove the lock cylinder from the handle; the installation process is the reverse of the removal process. For the latch, if not done earlier, remove the lock and inner handle rod, take the door latch retaining screws, and slowly pull the latch out of the door making sure not to bend the rods. Remove the lock and release rods from the latch assembly and replace it with new latch unit and installation process is just vice versa.

Genuine Honda Del Sol Door Latch Assembly

Door Latch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Door Latch Assemblys found

View related parts
Honda Del Sol Left Front Door Lock Assembly
Part Number: 72150-SR2-A12
Product Specifications
- Other Name: Lock Assembly; Lock
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1993-1997 Honda Del Sol | 2 Door S, 2 Door SI, 2 Door V-TEC | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Del Sol Right Front Door Lock Assembly
Part Number: 72110-SR2-A12
Product Specifications
- Other Name: Lock Assembly; Lock
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1993-1997 Honda Del Sol | 2 Door S, 2 Door SI, 2 Door V-TEC | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Del Sol Lock Assembly, Left Front Power Door
Part Number: 72150-SR2-A21
Product Specifications
- Other Name: Lock Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1995-1997 Honda Del Sol | 2 Door SI, 2 Door V-TEC | KA 4AT, KA 5MT
View related parts
Honda Del Sol Lock Assembly, Right Front Power Door
Part Number: 72110-SR2-A21
Product Specifications
- Other Name: Lock Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1995-1997 Honda Del Sol | 2 Door SI, 2 Door V-TEC | KA 4AT, KA 5MT

Honda Del Sol Door Latch Assembly

The Honda Del Sol Door Latch Assembly delivers the important lock that keeps every door firmly closed but with easy release when required to increase security and daily convenience. By being anchored to the body, the mechanism prevents unwanted entry, stops rattling on the road, and increases overall cabin safety. In earlier versions of the Honda Del Sol that applied manual locking levers, a simple mechanical assembly called the Door Latch Assembly had been applied, and the progressive versions of the Del Sol continued this basic robust latch structure, but with the connection to central locking actuators, there is a good case study that a single Door Latch Assembly can support both individual and collective lock commands. Regardless of which trim level is applied, all Del Sol door latch designs use a spring-loaded striker plate and claw inside the Door Latch Assembly to grip tight when the door closes, then release only after receiving the proper signal from the inside handle, outside handle, or the power lock. This simple yet durable unit does not require much maintenance, and due to the design being engineered specifically for Honda fitment, changes seamlessly from production year to year without changing door alignment. In short, the Honda system allows a Del Sol owner to rest assured that the Door Latch Assembly will lock easily every drive, whether initiated by the manual means or by the available central locking switch.

In search of affordable OEM Honda Del Sol Door Latch Assembly? Consider browsing through our extensive inventory of genuine Honda Del Sol Door Latch Assembly. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Del Sol Door Latch Assembly Parts Questions & Experts Answers

Left Front Door Lock Assembly
72150-SR2-A12
Q: How to replace the Door Handle, Door Latch Assembly, and Door Lock Cylinder on a Honda Del Sol?
A:
To replace the outside door handle, therefore, one has to take off the inside door handle, the Door Trim Panel as well as a plastic shield. Wind it around the handle opening since this is the area that the paint is most likely to get damaged. For rear doors, a position of rear glass channel must be changed, to do this , the upper channel nut has to be loosened and the lower bolt has to be removed then the channel has to be shifted forward. Secondly, thereafter, unscrew the door handle retaining bolts and if possible do away with the door latch so as to get better access to the door. With the help of a small flat-bladed screwdriver, pry the lock rod loose, pull the handle outwards from the door and turn it anti-clockwise to de-thread it from the release rod. The process of removal is done in an order of inversion to the process of installation. The lock cylinder can be replaced by first removing the outside door handle and by pulling a retainer clip to remove the lock cylinder from the handle; the installation process is the reverse of the removal process. For the latch, if not done earlier, remove the lock and inner handle rod, take the door latch retaining screws, and slowly pull the latch out of the door making sure not to bend the rods. Remove the lock and release rods from the latch assembly and replace it with new latch unit and installation process is just vice versa.