How to remove and install the distributor on Honda Prelude?

For two point two L and two point three L engines, observe the radio's theft prevention number before removing the battery. Start with unscrewing the negative terminal of the battery and then get at the bolt of the crankshaft pulley through the left side of the inner fender liner. Turn the engine anti-clockwise till the white TDC mark sits right on the pointer provided on the engine casing. When it is possible, do not remove the ignition wires from the distributor cap, but label them if it proves necessary; remove the distributor cap and make sure that the ignition rotor is in the right place. In case the marks are disturbed, rotate the crankshaft one full cycle in order to bring the TDC mark into view. If the distributor has to be reinstalled make alignment marks on the distributor housing and clyinder head, then disconnect the electrical connectors and remove three mounting bolts to take out the distributor. To install, crank the shaft to TDC or camshaft's UP mark facing up if the valve cover has been replaced. New O-ring should be treated with clean engine oil before being fitted to distributor shaft and distributor to be fitted into the cylinder head such that the offset lug pins into the camshaft groove. Tighten the mounting bolts by hand, redo the connection of the electrical connectors and put back the wires of ignition in the right manner before joining thae negative terminal of the battery. To reset the PCM idle memory turn on the engine and bring the engine to a 3000 rpms for a while then wait until it reaches the level where the cooling fan starts and then let the engine to idle for about five minutes with no accessories. After all, examine and set the ignition timing, also input the radio security code. In this case we need to remove the distributor, to do that the negative battery cable must be disconnected, 3-prong connector has to be detached from the distributor, ignition wires have to be matched and removed then the screws holding distributor to the cylinder head have to be loosened and distributor pulled away from it. In assembly, turn piston in the no.1 cylinder to TDC, apply light oil on a new O-ring and fit the distributor in the correct position that the offset drive shaft of the distributor is correctly positioned. Retighten the mounting bolts, reconnect the 3 prong connector; install the ignition wires, tighten the mounting bolts firmly and connect the negative battery clip to set baseline ignition. For 3.0L engines, the process is similar: pull the negative battery terminal; loosen the connector from the distributor terminal; align the marks, and unbolt the ignition wires; align the distributor, and remove the mounting bolts. For installation one should turn the piston #1 to the TDC, lubricate a new O-ring, insert the distributor into the housing, tighten the mounting bolts by hand, connect wires to the connector and put them in the proper places.

Genuine Honda Prelude Distributor

Ignition Distributor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

42 Distributors found

View related parts
Honda Prelude Distributor Assembly (Td-03V)
Part Number: 30100-PK1-672
$459.83 MSRP: $663.53
You Save: $203.70 (31%)
ADD TO CART
Limited Availability
Product Specifications
- Replaced by: 30105-PK1-902
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1988-1990 Honda Prelude | 2 Door 2.0S | KA 4AT
View related parts
Honda Prelude Distributor Assembly (Td-13C) (Tec)
Part Number: 30100-PC2-674
$434.01 MSRP: $626.28
You Save: $192.27 (31%)
ADD TO CART
Product Specifications
- Replaced by: 30105-PC2-672
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1982 Honda Prelude | 2 Door ** | KA HMT, KH HMT
View related parts
Honda Prelude Distributor Assembly (Td-14C) (Tec)
Part Number: 30100-PC2-693
$434.01 MSRP: $626.28
You Save: $192.27 (31%)
ADD TO CART
Product Specifications
- Replaced by: 30105-PC2-672
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1982 Honda Prelude | 2 Door ** | KL HMT
View related parts
Honda Prelude Distributor Assembly (Td-24C) (Tec)
Part Number: 30100-PC2-683
$448.89 MSRP: $647.76
You Save: $198.87 (31%)
ADD TO CART
Product Specifications
- Replaced by: 30105-PC1-006
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1982 Honda Prelude | 2 Door ** | KL 5MT
View related parts
Honda Prelude Distributor Assembly (Td-05V)
Part Number: 30100-PK1-692
$459.83 MSRP: $663.53
You Save: $203.70 (31%)
ADD TO CART
Product Specifications
- Replaced by: 30105-PK1-902
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1988-1990 Honda Prelude | 2 Door 2.0S | KL 4AT
View related parts
Honda Prelude Distributor Assembly (Td-13K) (Tec)
Part Number: 30100-PC7-662
$727.52 MSRP: $1049.82
You Save: $322.30 (31%)
ADD TO CART
Product Specifications
- Replaced by: 30105-PC7-662
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1984-1987 Honda Prelude | 2 Door DX | KA 5MT, KL 5MT
View related parts
Honda Prelude Distributor Assembly (Td-02P)
Part Number: 30100-PK2-006
Product Specifications
- Replaced by: 30100-PK2-036
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1988-1989 Honda Prelude | 2 Door 2.0SI | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Distributor Assembly (Td-76U) (Tec)
Part Number: 30100-P0B-A01
Product Specifications
- Other Name: Distributor Assembly; Distributor
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1996 Honda Prelude | 2 Door S | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Distributor Assembly (Td-02P)
Part Number: 30100-PK2-016
Product Specifications
- Replaced by: 30100-PK2-036
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1989 Honda Prelude | 2 Door 2.0SI | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Distributor Assembly (Td-02P)
Part Number: 30100-PK2-026
Product Specifications
- Replaced by: 30100-PK2-036
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1990-1991 Honda Prelude | 2 Door 2.05SI, 2 Door 2.0SI | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Distributor Assembly (Td-77U) (Tec)
Part Number: 30100-P5M-A01
Product Specifications
- Other Name: Distributor Assembly; Distributor
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1997-2001 Honda Prelude | 2 Door Base, 2 Door TYPESH | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Distributor Assembly
Part Number: 30100-P13-A01
Product Specifications
- Other Name: Distributor
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1996 Honda Prelude | 2 Door SI, 2 Door Sivtec | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Distributor Assembly (Td-61U) (Tec)
Part Number: 30100-P14-A01
Product Specifications
- Other Name: Distributor Assembly; Distributor
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1992-1995 Honda Prelude | 2 Door SI, 2 Door Sivtec | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Distributor Assembly (Td-59U) (Tec)
Part Number: 30100-P12-A01
Product Specifications
- Other Name: Distributor Assembly; Distributor
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1992-1995 Honda Prelude | 2 Door S | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Prelude Distributor Assembly (D4M7-05)
Part Number: 30100-689-661
Product Specifications
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1979 Honda Prelude | 2 Door ** | KA 5MT, KA HMT
View related parts
Honda Prelude Distributor Assembly (D4S8-03)
Part Number: 30100-689-662
Product Specifications
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1980 Honda Prelude | 2 Door ** | KA 5MT, KA HMT, KH 5MT, KH HMT
View related parts
Honda Prelude Distributor Assembly (D4S8-05)
Part Number: 30100-689-782
Product Specifications
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1980 Honda Prelude | 2 Door ** | KL 5MT
View related parts
Honda Prelude Distributor Assembly (Td-03H) (Tec)
Part Number: 30100-PC6-662
Product Specifications
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1983 Honda Prelude | 2 Door DX | KA 5MT, KL 5MT
View related parts
Honda Prelude Distributor Assembly (D4R80-23) (Hitachi)
Part Number: 30100-PC2-684
Product Specifications
- Replaces: 30100-PC2-681
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1982 Honda Prelude | 2 Door ** | KL 5MT
View related parts
Honda Prelude Distributor Assembly (D4R80-20) (Hitachi)
Part Number: 30100-PC2-665
Product Specifications
- Replaces: 30100-PC2-663, 30100-PC2-661
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1982 Honda Prelude | 2 Door ** | KA 5MT, KH 5MT

| Page 1 of 3 |Next >

1-20 of 42 Results

Honda Prelude Distributor

Honda Prelude vehicles require the Distributor for the ignition process where high voltage of current is delivered from the ignition coil to the spark plugs in the correct order known as firing order. Conventional Hondas Prelude models used mechanical distributor with breaker points, which are a wear component and periodically needed to be replaced. These distributors incorporated centrifugal and vacuum advanced mechanisms regarding spark timing based on certain engine parameters. The advances in technology led to the use of electronic distributors in Honda Prelude vehicles as opposed to mechanical ones, using Hall Effect or even optical sensors, thus making the vehicles more reliable and less requiring of maintenance. Distributor models in earlier designs used a single coil while today's models incorporate the use of COP or the distributor-less ignition system. Therefore it can be concluded that the change in the Distributor in Honda Prelude vehicles depicts the improvements of the ignition technology for improved fuel efficiency and environmentally friendly emissions.

In search of affordable OEM Honda Prelude Distributor? Consider browsing through our extensive inventory of genuine Honda Prelude Distributor. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Prelude Distributor Parts Questions & Experts Answers

Distributor Assembly (Td-77U) (Tec)
30100-P5M-A01
Q: How to remove and install the distributor on Honda Prelude?
A:
For two point two L and two point three L engines, observe the radio's theft prevention number before removing the battery. Start with unscrewing the negative terminal of the battery and then get at the bolt of the crankshaft pulley through the left side of the inner fender liner. Turn the engine anti-clockwise till the white TDC mark sits right on the pointer provided on the engine casing. When it is possible, do not remove the ignition wires from the distributor cap, but label them if it proves necessary; remove the distributor cap and make sure that the ignition rotor is in the right place. In case the marks are disturbed, rotate the crankshaft one full cycle in order to bring the TDC mark into view. If the distributor has to be reinstalled make alignment marks on the distributor housing and clyinder head, then disconnect the electrical connectors and remove three mounting bolts to take out the distributor. To install, crank the shaft to TDC or camshaft's UP mark facing up if the valve cover has been replaced. New O-ring should be treated with clean engine oil before being fitted to distributor shaft and distributor to be fitted into the cylinder head such that the offset lug pins into the camshaft groove. Tighten the mounting bolts by hand, redo the connection of the electrical connectors and put back the wires of ignition in the right manner before joining thae negative terminal of the battery. To reset the PCM idle memory turn on the engine and bring the engine to a 3000 rpms for a while then wait until it reaches the level where the cooling fan starts and then let the engine to idle for about five minutes with no accessories. After all, examine and set the ignition timing, also input the radio security code. In this case we need to remove the distributor, to do that the negative battery cable must be disconnected, 3-prong connector has to be detached from the distributor, ignition wires have to be matched and removed then the screws holding distributor to the cylinder head have to be loosened and distributor pulled away from it. In assembly, turn piston in the no.1 cylinder to TDC, apply light oil on a new O-ring and fit the distributor in the correct position that the offset drive shaft of the distributor is correctly positioned. Retighten the mounting bolts, reconnect the 3 prong connector; install the ignition wires, tighten the mounting bolts firmly and connect the negative battery clip to set baseline ignition. For 3.0L engines, the process is similar: pull the negative battery terminal; loosen the connector from the distributor terminal; align the marks, and unbolt the ignition wires; align the distributor, and remove the mounting bolts. For installation one should turn the piston #1 to the TDC, lubricate a new O-ring, insert the distributor into the housing, tighten the mounting bolts by hand, connect wires to the connector and put them in the proper places.