How to Replace the Ignition Lock Cylinder and Ignition Switch on a Honda Ridgeline?

A one-piece assembly is The Ignition Lock Cylinder and ignition switch assembly, which is also referred to as the "steering lock". If either the Ignition Lock Cylinder or the ignition switch fails, replace the assembly. Unplug negative battery terminal using cable followed by waiting for not less than three minutes. It is necessary to remove knee bolster and upper and lower steering column covers. Turn over driver's side fuse and relay box in order to reach panel backside. Trace electrical harness down from Ignition Lock Cylinder/ignition switch assembly towards driver's side fuse and relay box, detach any harness clips, then disconnect ignition switch electrical connector from fuse and relay box. Detach clip of driver's side airbag wiring harness from bracket on Ignition Lock Cylinder/ignition switch assembly. Disconnect small electrical connector from Ignition Lock Cylinder/ignition switch assembly. Center-punch two shear-head bolts that secure mounting clamp for Ignition Lock Cylinder/ignition switch assembly, next drill out center of each bolt removing bolts with use of screw extractor. Another possible way might be using a hammer chisel to knock off bolts in a counterclockwise direction. Remove bracket then separate lock cylinder/ignition switch assembly at steering column. Reverse steps for installation process after completing removal process hereinabove outlined in steps 1 through 14. Tighten new shear-head bolts until heads break off completely. After finishing reconnect cable back onto negative battery terminal again Verify proper functioning of Ignition Lock Cylinder/ignition switch assembly.

Genuine Honda Ridgeline Ignition Switch

Starter Ignition Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Ignition Switches found

View related parts
Honda Ridgeline Switch Assembly
Part Number: 35881-TG7-A04
$91.70 MSRP: $132.90
You Save: $41.20 (31%)
ADD TO CART
Product Specifications
- Other Name: Power Switch, Start Button
- Replaces: 35881-TG7-A01, 35881-TG7-A02, 35881-TG7-A03
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2026 Honda Ridgeline | 4 Door Black, 4 Door Black Edition, 4 Door Black Edition AWD, 4 Door Black Edition Two-Tone, 4 Door RT (2WD), 4 Door RT (AWD), 4 Door RTL, 4 Door RTL (2WD), 4 Door RTL (AWD), 4 Door RTL AWD, 4 Door RTL-E AWD, 4 Door RTS (2WD), 4 Door RTS (AWD), 4 Door Sport, 4 Door Sport (2WD), 4 Door Sport (AWD), 4 Door Sport AWD, 4 Door TrailSport, 4 Door TrailSport AWD, 4 Door TrailSport With HPD Wheels | 9AT, KA 6AT, KA 9AT
View related parts
Honda Ridgeline Switch Assembly, Engine Start & Stop
Part Number: 35881-TG7-A03
$91.70 MSRP: $132.90
You Save: $41.20 (31%)
ADD TO CART
Product Specifications
- Replaced by: 35881-TG7-A04
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2020 Honda Ridgeline | 4 Door Black, 4 Door RT (2WD), 4 Door RT (AWD), 4 Door RTL, 4 Door RTL (2WD), 4 Door RTL (AWD), 4 Door RTS (2WD), 4 Door RTS (AWD), 4 Door Sport (2WD), 4 Door Sport (AWD) | KA 6AT, KA 9AT
View related parts
Honda Ridgeline Switch Assembly, Engine Start & Stop
Part Number: 35881-TG7-A01
$91.70 MSRP: $132.90
You Save: $41.20 (31%)
ADD TO CART
Product Specifications
- Replaced by: 35881-TG7-A04
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017 Honda Ridgeline | 4 Door Black, 4 Door RT (2WD), 4 Door RT (AWD), 4 Door RTL, 4 Door RTL (2WD), 4 Door RTL (AWD), 4 Door RTS (2WD), 4 Door RTS (AWD), 4 Door Sport (2WD), 4 Door Sport (AWD) | KA 6AT
View related parts
Honda Ridgeline Switch, Steering
Part Number: 35130-SJC-A01
$76.75 MSRP: $108.40
You Save: $31.65 (30%)
ADD TO CART
Product Specifications
- Other Name: Ignition Switch
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2006-2014 Honda Ridgeline | 4 Door RT, 4 Door RTL, 4 Door RTS, 4 Door RTX, 4 Door Sport | KA 5AT
View related parts
Honda Ridgeline Switch Assembly, Engine Start & Stop
Part Number: 35881-TG7-A02
$91.70 MSRP: $132.90
You Save: $41.20 (31%)
ADD TO CART
Product Specifications
- Replaced by: 35881-TG7-A04
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2017-2019 Honda Ridgeline | 4 Door Black, 4 Door RT (2WD), 4 Door RT (AWD), 4 Door RTL, 4 Door RTL (2WD), 4 Door RTL (AWD), 4 Door RTS (2WD), 4 Door RTS (AWD), 4 Door Sport (2WD), 4 Door Sport (AWD) | KA 6AT

Honda Ridgeline Ignition Switch

The Ignition switch of the Honda Ridgeline, which is also called the starter switch, is incredibly important when it comes to the starting of the ignition as well as the charging techniques of the car. By twisting the ignition switch using the key or pressing the button or depending on the newer models of the automobile using a remote the Honda Ridgeline sends a message to the computer that some important connection has happened to start the engines and run the automobile. In the old days, Honda Ridgeline cars used essential mechanical keys that were used to trigger the ignition switch, thus releasing the system for the rightful key. But nowadays some systems have replaced the mechanical lazer with a push button which is still keyed in through a transponder signal. Such evolution is an indication of the improvement of vehicle technologies where the primary functions of the ignition switch in powering the starter solenoid and ignition parts remain unchanged. In general, the Ignition Switch for Honda Ridgeline keeps its importance as non-complex and unique fixed part for the particular model with ease of replacement.

In search of affordable OEM Honda Ridgeline Ignition Switch? Consider browsing through our extensive inventory of genuine Honda Ridgeline Ignition Switch. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Ridgeline Ignition Switch Parts Questions & Experts Answers

Switch, Steering
35130-SJC-A01
Q: How to Replace the Ignition Lock Cylinder and Ignition Switch on a Honda Ridgeline?
A:
A one-piece assembly is The Ignition Lock Cylinder and ignition switch assembly, which is also referred to as the "steering lock". If either the Ignition Lock Cylinder or the ignition switch fails, replace the assembly. Unplug negative battery terminal using cable followed by waiting for not less than three minutes. It is necessary to remove knee bolster and upper and lower steering column covers. Turn over driver's side fuse and relay box in order to reach panel backside. Trace electrical harness down from Ignition Lock Cylinder/ignition switch assembly towards driver's side fuse and relay box, detach any harness clips, then disconnect ignition switch electrical connector from fuse and relay box. Detach clip of driver's side airbag wiring harness from bracket on Ignition Lock Cylinder/ignition switch assembly. Disconnect small electrical connector from Ignition Lock Cylinder/ignition switch assembly. Center-punch two shear-head bolts that secure mounting clamp for Ignition Lock Cylinder/ignition switch assembly, next drill out center of each bolt removing bolts with use of screw extractor. Another possible way might be using a hammer chisel to knock off bolts in a counterclockwise direction. Remove bracket then separate lock cylinder/ignition switch assembly at steering column. Reverse steps for installation process after completing removal process hereinabove outlined in steps 1 through 14. Tighten new shear-head bolts until heads break off completely. After finishing reconnect cable back onto negative battery terminal again Verify proper functioning of Ignition Lock Cylinder/ignition switch assembly.