How to remove and install the front crankshaft pulley and Crankshaft Seal on Four cylinder engine on Honda Accord?

So as to remove the crankshaft pulley follow the steps; switch off the engine and then unbolt the cable of the negative terminal. Then, it is required to lift the vehicle and steady it with jackstands. After this, you can then take off the splash shield found at the underside of the engine compartment and the drivebelt. I would encourage the use of a breaker bar and socket to remove the crankshaft pulley center bolt, but it's important the pulley be locked into place in some way with a strap wrench or a special tool that the mechanic can secure to the wheel, which requires that a shop rag be wrapped around the pulley. Pull the pulley of the crankshaft and then eject the crankshaft front oil seal with a seal puller or by using the tip of the screwed screw driver though the tip has tape around it so that it will not harm the crankshaft. As an example, the seal bore must be cleaned carefully and must be checked for nicks or gouges and the hub area may exhibit abnormal wear or scoring; many popular engines may have a repair sleeve. When installing, the lip of the new seal must be rubbed in clean engine oil and the seal installed with the aid of a seal driver or a socket just slightly smaller than the seal with the open side towards the engine. I put some clean engine oil on the sealing surface of the hub, fitted the crankshaft pulley and tightened the bolt to recommended torque. Last but not the least, you can finish the installation process by going through the removal process in reverse and reconnect the battery.

Genuine Honda Accord Crankshaft Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

35 Crankshaft Seals found

View related parts
Honda Accord Oil Seal (43X58X7)
Part Number: 91212-R1B-A01
$6.16 MSRP: $8.70
You Save: $2.54 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal; Crankshaft Seal, Front Cover Seal, Oil Seal, Seal
- Replaces: 91212-R40-A01, 91212-RNA-A01, 91212-R11-A01, 91212-RTA-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2014 Honda Accord | 4 Door Hybrid | KA CVT
- 2006-2012 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door EX-SUL, 2 Door LX, 2 Door LX-S, 2 Door LX-SUL, 4 Door EX, 4 Door EX (PZEV), 4 Door EX-L, 4 Door EX-L (PZEV), 4 Door LX, 4 Door LX (PZEV), 4 Door SE, 4 Door SE (PZEV), 4 Door VP | KA 5AT, KA 5MT, KL 5AT, KL 5MT
View related parts
Honda Accord Oil Seal (80X100X10) (Nok)
Part Number: 91214-PLE-003
$34.76 MSRP: $49.52
You Save: $14.76 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaces: 91214-PAA-A01, 91214-PLM-A02, 91214-PR4-A01, 91214-P2F-A01, 91214-PH1-661, 91214-PAA-A02, 91214-PH1-013, 91214-PH1-003, 91214-PD2-004, 91214-PLC-003, 91214-PT0-004, 91214-PC6-013, 91214-P7A-004, 91214-PE1-721, 91214-PLC-004, 91214-PLM-A01, 91214-PC6-003, 91214-PH1-004, 91214-PH3-751, 91214-PC7-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1984-2002 Honda Accord | 2 Door DX, 2 Door EX, 2 Door LX, 2 Door LXI, 2 Door SE, 2 Door SEI, 2 Door Special, 3 Door DX, 3 Door LX, 3 Door LXI, 3 Door S, 4 Door DX, 4 Door DX-VP, 4 Door EX, 4 Door EX-L, 4 Door EX-SUL, 4 Door EX-UL, 4 Door LX, 4 Door LXI, 4 Door SE, 4 Door SE-UL, 4 Door SEI, 4 Door Special, 4 Door STD, 4 Door VP, 5 Door EX, 5 Door LX | KA 4AT, KA 5MT, KH 4AT, KH 5MT, KL 4AT, KL 5MT
View related parts
Honda Accord Oil Seal (41X56X7)
Part Number: 91212-5MR-A01
$10.47 MSRP: $14.92
You Save: $4.45 (30%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Seal, Front Crank Seal
- Replaces: 91212-R70-A02, 91212-RCA-A02, 91212-R70-A01, 91212-RCA-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2003-2017 Honda Accord | 2 Door EX (V6), 2 Door EX V6, 2 Door EX-L V6, 2 Door EX-V6, 2 Door LX (V6), 2 Door LX V6, 2 Door SE (V6), 2 Door Touring (V6), 2 Door TRN-V6, 4 Door EX (V6), 4 Door EX-L V6, 4 Door EX-V6, 4 Door EX-V6 (PZEV), 4 Door LX (V6), 4 Door SE (V6), 4 Door Touring (V6) | KA 5AT, KA 6AT, KA 6MT, KL 5AT, KL 6AT, KL 6MT
View related parts
Honda Accord Oil Seal (41X56X7) (Nok)
Part Number: 91212-R70-A02
$10.47 MSRP: $14.92
You Save: $4.45 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal
- Replaced by: 91212-5MR-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2003-2017 Honda Accord | 2 Door EX (V6), 2 Door EX V6, 2 Door EX-L V6, 2 Door EX-V6, 2 Door LX (V6), 2 Door LX V6, 2 Door SE (V6), 2 Door Touring (V6), 2 Door TRN-V6, 4 Door EX (V6), 4 Door EX-L V6, 4 Door EX-V6, 4 Door EX-V6 (PZEV), 4 Door LX (V6), 4 Door SE (V6), 4 Door Touring (V6) | KA 5AT, KA 6AT, KA 6MT, KL 5AT, KL 6AT, KL 6MT
View related parts
Honda Accord Oil Seal (43X58X7)
Part Number: 91212-59B-003
$23.53 MSRP: $33.52
You Save: $9.99 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal; Crankshaft Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2016-2025 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door LX-S, 4 Door (2.0 Sport), 4 Door (2.0 Touring), 4 Door 1.5T EX, 4 Door 1.5T EX BD, 4 Door 1.5T EX-L, 4 Door 1.5T LX, 4 Door 1.5T SE, 4 Door 1.5T Sport, 4 Door 1.5T Sport SE, 4 Door 2.0T Sport, 4 Door 2.0T Touring, 4 Door EX, 4 Door EX-L, 4 Door EX-L (2.0), 4 Door LX, 4 Door SE, 4 Door Sport, 4 Door Touring | 10AT, CVT, KA 6MT, KA CVT, KA XAT, KL CVT
View related parts
Honda Accord Oil Seal (80X98X8) (Nok)
Part Number: 91214-RKG-003
$34.91 MSRP: $49.73
You Save: $14.82 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaces: 91214-RCA-A01, 91214-RBB-003, 91214-R70-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2003-2017 Honda Accord | 2 Door EX (V6), 2 Door EX V6, 2 Door EX-L V6, 2 Door EX-V6, 2 Door LX (V6), 2 Door LX V6, 2 Door SE (V6), 2 Door Touring (V6), 2 Door TRN-V6, 4 Door EX (V6), 4 Door EX-L V6, 4 Door EX-V6, 4 Door EX-V6 (PZEV), 4 Door LX (V6), 4 Door SE (V6), 4 Door Touring (V6) | KA 5AT, KA 6AT, KA 6MT, KL 5AT, KL 6AT, KL 6MT
View related parts
Honda Accord Oil Seal (43X58X7) (Nok)
Part Number: 91212-PNC-003
$15.91 MSRP: $22.67
You Save: $6.76 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Cover Seal; Cover Seal, Oil Seal, Seal
- Replaces: 91212-PNA-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2003-2005 Honda Accord | 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door LX | KA 5AT, KA 5MT, KL 5AT
View related parts
Honda Accord Oil Seal (41X56X7) (Arai)
Part Number: 91212-R70-A01
$10.47 MSRP: $14.92
You Save: $4.45 (30%)
ADD TO CART
Product Specifications
- Replaced by: 91212-5MR-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2003-2017 Honda Accord | 2 Door EX (V6), 2 Door EX V6, 2 Door EX-L V6, 2 Door EX-V6, 2 Door LX (V6), 2 Door LX V6, 2 Door SE (V6), 2 Door Touring (V6), 2 Door TRN-V6, 4 Door EX (V6), 4 Door EX-L V6, 4 Door EX-V6, 4 Door EX-V6 (PZEV), 4 Door LX (V6), 4 Door SE (V6), 4 Door Touring (V6) | KA 5AT, KA 6AT, KA 6MT, KL 5AT, KL 6AT, KL 6MT
View related parts
Honda Accord Oil Seal (80X98X10) (Arai)
Part Number: 91214-RZY-A01
$19.02 MSRP: $27.10
You Save: $8.08 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaces: 91214-PWA-Y01, 91214-RZA-004
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2008-2012 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door LX, 2 Door LX-S, 4 Door EX, 4 Door EX (PZEV), 4 Door EX-L, 4 Door EX-L (PZEV), 4 Door LX, 4 Door LX (PZEV), 4 Door SE, 4 Door SE (PZEV) | KA 5AT, KA 5MT, KL 5AT, KL 5MT
View related parts
Honda Accord Oil Seal (80X98X10)
Part Number: 91214-5A2-A01
$17.04 MSRP: $24.07
You Save: $7.03 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaces: 91214-RE0-H01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2013-2022 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door LX-S, 4 Door (2.0 Sport), 4 Door (2.0 Touring), 4 Door 2.0T Sport, 4 Door 2.0T Touring, 4 Door EX, 4 Door EX-L, 4 Door EX-L (2.0), 4 Door LX, 4 Door SE, 4 Door Sport | 10AT, KA 6MT, KA CVT, KA XAT, KL 6MT, KL CVT
View related parts
Honda Accord Oil Seal,Low Torq
Part Number: 91214-59B-003
$14.73 MSRP: $20.80
You Save: $6.07 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2018-2025 Honda Accord | 4 Door 1.5T EX, 4 Door 1.5T EX BD, 4 Door 1.5T EX-L, 4 Door 1.5T LX, 4 Door 1.5T SE, 4 Door 1.5T Sport, 4 Door 1.5T Sport SE, 4 Door EX, 4 Door EX-L, 4 Door LX, 4 Door Sport, 4 Door Touring | CVT, KA 6MT, KA CVT
View related parts
Honda Accord Oil Seal (43X58X7) (Arai)
Part Number: 91212-PNC-004
$12.06 MSRP: $17.03
You Save: $4.97 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Cover Seal; Oil Seal, Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2003-2005 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door LX, 2 Door SE, 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door LX | KA 5AT, KA 5MT, KL 5AT, KL 5MT
View related parts
Honda Accord Oil Seal (43X58X7) (Nok)
Part Number: 91212-RTA-003
$6.16 MSRP: $8.70
You Save: $2.54 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Cover Seal
- Replaced by: 91212-R1B-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2014 Honda Accord | 4 Door Hybrid | KA CVT
- 2011 Honda Accord | 4 Door LX | KA 5AT
- 2006-2009 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door LX, 4 Door EX, 4 Door EX (PZEV), 4 Door EX-L, 4 Door EX-L (PZEV), 4 Door LX, 4 Door LX (PZEV), 4 Door SE, 4 Door VP | KA 5AT, KA 5MT, KL 5AT
View More
View related parts
Honda Accord Oil Seal (80X98X8) (Nok)
Part Number: 91214-RCA-A01
$34.91 MSRP: $49.73
You Save: $14.82 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaced by: 91214-RKG-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2003-2017 Honda Accord | 2 Door EX (V6), 2 Door EX V6, 2 Door EX-L V6, 2 Door EX-V6, 2 Door LX (V6), 2 Door LX V6, 2 Door SE (V6), 2 Door Touring (V6), 2 Door TRN-V6, 4 Door EX (V6), 4 Door EX-L V6, 4 Door EX-V6, 4 Door EX-V6 (PZEV), 4 Door LX (V6), 4 Door SE (V6), 4 Door Touring (V6) | KA 5AT, KA 6AT, KA 6MT, KL 5AT, KL 6AT, KL 6MT
View related parts
Honda Accord Oil Seal (40X52X7) (Nok)
Part Number: 91212-PAA-A01
$17.02 MSRP: $24.03
You Save: $7.01 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal
- Replaces: 91212-PAA-A02
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1998-2002 Honda Accord | 2 Door EX, 2 Door LX, 2 Door SE, 4 Door DX, 4 Door EX, 4 Door EX-L, 4 Door EX-SUL, 4 Door EX-UL, 4 Door LX, 4 Door SE, 4 Door SE-UL, 4 Door VP | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Accord Oil Seal (40X52X7) (Arai)
Part Number: 91212-P0A-004
$16.67 MSRP: $23.75
You Save: $7.08 (30%)
ADD TO CART
Product Specifications
- Replaces: 91212-PT0-003
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1990-1997 Honda Accord | 2 Door DX, 2 Door EX, 2 Door LX, 2 Door SE, 2 Door Special, 4 Door DX, 4 Door DX-VP, 4 Door EX, 4 Door LX, 4 Door SE, 4 Door Special, 5 Door EX, 5 Door LX | KA 4AT, KA 5MT, KL 4AT, KL 5MT
View related parts
Honda Accord Oil Seal (41X56X8)
Part Number: 91212-P8A-A01
$14.62 MSRP: $20.65
You Save: $6.03 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1998-2002 Honda Accord | 2 Door EX (V6), 2 Door LX (V6), 4 Door EX (V6), 4 Door EX-V6, 4 Door LX (V6), 4 Door LX V6 | KA 4AT, KL 4AT
View related parts
Honda Accord Oil Seal (43X58X7)
Part Number: 91212-5A2-A01
$27.55 MSRP: $38.92
You Save: $11.37 (30%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal; Crankshaft Seal
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 2013-2014 Honda Accord | 2 Door EX, 2 Door EX-L, 2 Door LX-S, 4 Door EX, 4 Door EX-L, 4 Door LX, 4 Door Sport | KA 6MT, KA CVT, KL 6MT, KL CVT
View related parts
Honda Accord Oil Seal (80X98X10) (Nok)
Part Number: 91214-P8A-A01
$13.74 MSRP: $19.57
You Save: $5.83 (30%)
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal
- Replaced by: 91214-RNB-A01
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1998-2002 Honda Accord | 2 Door EX (V6), 2 Door LX (V6), 4 Door EX (V6), 4 Door EX-V6, 4 Door LX (V6), 4 Door LX V6 | KA 4AT, KL 4AT
View related parts
Honda Accord Oil Seal (80X98X10) (Arai)
Part Number: 91214-RNB-A01
$13.85 MSRP: $19.57
You Save: $5.72 (30%)
Product Specifications
- Other Name: Rear Main Seal
- Replaces: 91214-PH7-013, 91214-PY3-003, 91214-P8A-A01, 91214-PH7-003, 91214-PWA-003, 91214-RTA-004, 91214-PH7-004, 91214-PNA-014, 91214-PL2-004
- Warranty: This genuine part is guaranteed by Honda's factory warranty.
Fits the following Vehicles:
- 1995-2007 Honda Accord | 2 Door EX, 2 Door EX (V6), 2 Door EX-L, 2 Door EX-SUL, 2 Door LX, 2 Door LX (V6), 2 Door LX-SUL, 2 Door SE, 4 Door DX, 4 Door EX, 4 Door EX (V6), 4 Door EX-L, 4 Door EX-V6, 4 Door LX, 4 Door LX (V6), 4 Door LX V6, 4 Door SE, 4 Door VP | KA 4AT, KA 5AT, KA 5MT, KL 4AT, KL 5AT, KL 5MT

| Page 1 of 2 |Next >

1-20 of 35 Results

Honda Accord Crankshaft Seal

The Crankshaft Seal is part of Honda Accord vehicles that is situated at the front of the engine, its main function is to stop oil from leaking out of the crankcase. Made from metal and rubber this round seal is commonly positioned to ensure that the lubrication of an engine is well achieved in order to minimize on friction and wear on the part of the engine. Different types of Crankshaft Seal have been used for different generations of Honda Accord with minor changes in material and structure for improving sturdiness and output. They may need replacement in high mileage cars, and a worn or damaged Crankshaft Seal can cause oil leaks hence the need to have it replace so that the car's engine runs smoothly. Further, the Honda Accord's Crankshaft Seal is critical to the overall performance of the engine, and its maintenance must be a regular process.

In search of affordable OEM Honda Accord Crankshaft Seal? Consider browsing through our extensive inventory of genuine Honda Accord Crankshaft Seal. Not only do we provide market-leading prices and a manufacturer's warranty, but we also pride ourselves on exceptional customer service and swift delivery.

Honda Accord Crankshaft Seal Parts Questions & Experts Answers

Oil Seal (43X58X7) (Arai)
91212-PNC-004
Q: How to remove and install the front crankshaft pulley and Crankshaft Seal on Four cylinder engine on Honda Accord?
A:
So as to remove the crankshaft pulley follow the steps; switch off the engine and then unbolt the cable of the negative terminal. Then, it is required to lift the vehicle and steady it with jackstands. After this, you can then take off the splash shield found at the underside of the engine compartment and the drivebelt. I would encourage the use of a breaker bar and socket to remove the crankshaft pulley center bolt, but it's important the pulley be locked into place in some way with a strap wrench or a special tool that the mechanic can secure to the wheel, which requires that a shop rag be wrapped around the pulley. Pull the pulley of the crankshaft and then eject the crankshaft front oil seal with a seal puller or by using the tip of the screwed screw driver though the tip has tape around it so that it will not harm the crankshaft. As an example, the seal bore must be cleaned carefully and must be checked for nicks or gouges and the hub area may exhibit abnormal wear or scoring; many popular engines may have a repair sleeve. When installing, the lip of the new seal must be rubbed in clean engine oil and the seal installed with the aid of a seal driver or a socket just slightly smaller than the seal with the open side towards the engine. I put some clean engine oil on the sealing surface of the hub, fitted the crankshaft pulley and tightened the bolt to recommended torque. Last but not the least, you can finish the installation process by going through the removal process in reverse and reconnect the battery.